Ls Automatic Compression Testers For Concrete Cylinders Moulds

TESTMAK ASTM series Fully Automatic Low Capacity Concrete Compression Machines have a total capacity of 250,000lbf (1,112 kN) and 325,000lbf (1,446 kN) their rugged, welded steel frames exceed ACI 363 requirements for system rigidity. They perform complete strength tests for concrete cylinders, beams, cubes, cores, and other sample types.
The device is suitable for do testing in AASHTO T 22 , BS 1610 , BS 1881 , ASTM C109/109M , ASTM C293/293M , ASTM C39/39M , ASTM C78/78M standards.

The units are supplied ready for compression strength testing of 6x12in (152x305mm) concrete cylinders up to 12,700psi (87.6mPa) with user-supplied unbonded neoprene capping pads and steel retainers.
Can do tested with a single button on the TCM200 touchscreen controller after the selection of the test method, sample type, specimen data, and test parameters are made.

Testable Specimens
• Concrete Cubes:
4in and 6in concrete cube specimens or any other custom cube and prism size can be tested with this machine.
• Concrete Cylinder:
4in and 6in diameter concrete cylinder specimens or any other custom diameters cylinder can be tested with this machine.

The piston is covered with a protective panel so that it is not affected by accumulated test residues. The hydraulic power unit is designed independently of the machine to prevent excessive and long-term wear. Emergency stop button, hydraulic safety relief valve, piston overtravel limit switch and part guard gate provide safety for the operator while tests are being performed.


Safety Features
Maximum pressure valves to avoid machine overloading
Limit switch (for piston stroke)
Emergency stop button
Removable transparent front and rear safety doors
Software controlled maximum load value
Security Switch for to stop the machine if the door is opened during a test.

Hydraulic Power Pack
The integrated electric motor and the high pressure hydraulic pump are energy efficient and operate at variable speeds to achieve and maintain required pressures based on loading program demands. This state-of-the-art drive system is dramatically quieter, eliminates pressure variations from over-heated oil, and extends the service life of the hydraulic components.



TCM200 Touchscreen Controls
The TCM200 touchscreen controls specimen contact, pre-loading, rate of load, break detection, data collection, and return of the piston to the home position following specified requirements for the selected test method.

Advantages of TCM200 touch screen control and data acquisition unit
1-) Values of 6in or 150mm concrete cube samples such as dimensions, test speed and fracture sensitivity rate are automatically predefined in the device.
2-) Values of 6x12in (152x305mm) concrete cylinder samples such as dimensions, test speed and fracture sensitivity rate are automatically predefined in the device.
3-) If you want to enter special values, you can easily change or add them on the touch screen.

Force, stress, and rate of load are displayed simultaneously during a test, with an option to show real-time load vs time or stress vs strain graphs. Load rate and applied force are precisely regulated by feedback during sample loading. Tests can be printed immediately using the Wi-Fi capability, or the data can easily be collected and transferred to the user’s PC for reporting results using a with SD card drive and the USB ports.



A menu button prints each test or transfers test data in summary form. Testing laboratory, sample ID, and client information are stored for error-free reporting and distribution. The diagnostics feature instantly displays the status of the emergency-stop button, drive system, data communication, pressure transducer, and over-travel limit switch. If any of the systems indicate a fault condition, it must be resolved before testing can proceed.

TCM200 Touch Control Unit



TCM200 Touch Control Unit is designed to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Testmak automatic compression / flexure testing machines.
All the operations of TCM200 Touch are controlled from the front panel touch screen display.
TCM200 Touch Control Unit has easy to use menu options. It displays all menu option listings simultaneously, allowing the operator to access the required option in a seemless manner to activate the option or enter a numeric value to set the test parameters. Digital graphic display is able to draw real-time "Load vs. Time", or "Stress vs. Time" graphics. Can do calibration easily from 10 points. Manual Control is available.

Technicial Features for TCM200 Touch Screen
• Color TFT touch display supports 16M colors and supports 800x480 pixel screen resolution
• 3 pcs universal analog input sockets (ADC)
• Each analog input with 18 bit precision (1/256000)
• 1 replacement analog input
• Total of 4 analog high-precision measuring capacities
• 2 analog output sockets (DAC)
• PULSE / DIR outputs (PULSE / DIR / ENA) to control the servo and stepper motor drives.
• Digital outputs for general purpose (can pull relays and control different electrical units)
• Digital inputs for general purpose (receives and evaluates input signals like limit contacts from the environment)
• Potentiometer input (reference signal input for calibration and remote control)
• USB communication signal output (communicates with computers)
• Connects to local networks and the Internet with Ethernet 10/100 network connection output (optional)
• Connects to portable devices via Bluetooth wireless connection (optional)
• 500 test results can be stored in internal memory
• Due to the SD (memory) card connection, a large number of test results can be stored in the device memory (40,000 test results).
• In addition, the results can be taken from the device memory and transferred to the computer as an Excel table. (Optional)
• Resistive touch screen allows easy operation of device functions by touching the screen
• Sensor modules are compatible with loadcell (load cell), pressure sensor (4-20 / 0-20 mA), potentiometric distance sensors, strain washers, thermocouples and all kinds of mV output sensors.
• Provides precise calibration with multi-point calibration (up to 10 points)
• Setting and calibration menus are password protected and prevent unauthorized use
• Allows testing with a computer, tablet, smartphone or on the touch screen panel.
• There are many test sample information screens and test methods in the device memory and tests can be performed easily
• Different menu languages can be selected via the device via language support (Turkish, English, French, Spanish and Russian)
• Speed control algorithm is closed loop PID control and all parameters can be adjusted on user side.
• The device can switch between one-touch load and deformation control modesCihaz farklı makinelere kolayca adapte edilebilir ve en uygun kontrol sağlanır
• The graphical field that visualizes the test results on the screen has the ability to change the scale automatically and automatically adjusts the optimal scale as the values change
• Firmware updates can be made via USB input. In addition, via the computer allows remote or internet update.

TCM200 Touch Software for Automatic Compression / Flexure Testing Machines



TCM200 Touch software provides to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Testmak automatic compression / flexure testing machines.

ASTM Low Capacity Automatic Compression Testers send complete with following accessories;
1- Spacer Discs for ASTM Standards
• 6 x 4in (152.4 x 101.6 mm), Dia. x H spacer disc 1 piece
• 6 x 3in (152.4 x 76.2 mm), Dia. x H spacer disc 1 piece
• 6 x 2in (152.4 x 50.8 mm), Dia. x H spacer disc 1 piece
• 6 x 1in (152.4 x 25.4 mm), Dia. x H spacer disc 1 piece
2- Upper Platen;
• Upper Platen: 6.5in (165.1mm) dia. (with ball seating assembly)
3- Lower Platen;
• Lower Platen: 6.5in (165.1mm) dia.
4- Piston;
• Piston Diameter 6in (152.4mm) (For C5200)
• Piston Diameter 8in (203.2mm) (For C5215)
5- Automatic Hydraulic Power Pack ;
• Automatic Hydraulic Power Pack, 350 bar (For C5200)
• Automatic Hydraulic Power Pack, 450 bar (For C5215)
6- Safety Doors
• • Removable transparent front and rear safety doors
7- Touch screen control panel and data acquisition unit
• 7 inch Touch screen control panel and data acquisition unit.
8- PC Software
• PC Software for Compression machine